{"id":1587,"date":"2012-02-11T20:19:59","date_gmt":"2012-02-11T20:19:59","guid":{"rendered":"http:\/\/www.audioexcite.com\/?page_id=1587"},"modified":"2012-12-23T09:24:41","modified_gmt":"2012-12-23T09:24:41","slug":"audiotechnology-15h520613sdk","status":"publish","type":"page","link":"https:\/\/www.audioexcite.com\/?page_id=1587","title":{"rendered":"AudioTechnology 15H520613SDK"},"content":{"rendered":"

Overview:<\/span><\/h3>\n

 <\/p>\n

\"\"<\/a>The 15H 52 06 13 SDK is a mid-woofer from the AudioTechnology C-Quenze series.<\/p>\n

The best part of energy during development was put into refinement of the performance in the midrange area. All the materials used, were picked to obtain the trustworthiest midrange reproduction. The drivers are extremely fast and move without any dynamic compression due to the mechanical construction.<\/p>\n

Customers are able to make adjustments regarding the T\/S parameters as well as the physical parameters \u2013 FX. Voice coil winding height, magnetic gap height and magnet sizes. This is an unique possibility for DIY:ers.<\/p>\n

The features such as: SD system, Kapton voice-coil former and under-hung motor structure is available in the C-Quenze drivers. Hexacoil voice coil winding technique is used.<\/p>\n

The high ventilation factor through the centre pole piece, under the rear suspension and the perforation to the voice coil, are naturally kept intact, enabling the moving system to accelerate without any compression.<\/p>\n

Note!<\/strong> The drivers measured and used here are a custom built driver (“SDK” version) with an under-hung voice-coil made of Kapton. Drivers with Kapton voice-coil former often perform a more detailed midrange with higher dynamic and less coloration and distortion.<\/p>\n

AudioTechnology spec sheet: C-Quenze 15 H 52 06 13 SD<\/a><\/p>\n

T\/S Parameters:<\/span><\/h3>\n

 <\/p>\n

\"\"<\/a>
\nT\/S parametrs are measured both when the driver unit are cold and when warmed up with a 1 hour stress stimulus\u00a0 at 5.66V (4W\/8\u03a9). The warmed up driver units are rested for 2-3 minutes before they are measured.<\/p>\n

 <\/p>\n

 <\/p>\n

 <\/p>\n

 <\/p>\n

Impedance:<\/span><\/h3>\n

 <\/p>\n

\"\"<\/a><\/p>\n

Free air impedance measurement \u201ccold\u201d driver units:<\/p>\n

Sample 1 = Green<\/p>\n

Sample 2 = Blue<\/p>\n

The samples are an almost perfect match between each other. Some sort of resonance is visible at 1250Hz.\u00a0Very low inductance.<\/p>\n

 <\/p>\n

 <\/p>\n

\"\"<\/a><\/p>\n

Free air impedance measurement \u201chot\u201d driver units:<\/p>\n

Sample 1 = Green<\/p>\n

Sample 2 = Blue<\/p>\n

The Fs is lowered by 3Hz, but otherwise they have the same response curve as the \u201ccold\u201d driver units.<\/p>\n

 <\/p>\n

 <\/p>\n

Frequency:<\/span><\/h3>\n

 <\/p>\n

Frequency measurement conditions:<\/strong><\/p>\n

The mid-woofer is measured mounted in a 14 liter Dayton Audio enclosure (PartsExpress part #302-721) baffle with the following conditions:<\/p>\n

Baffle size (WxH):<\/strong> 21,59\u00d735,56cm (8,5\u2033x14\u2033)<\/p>\n

Driver position:<\/strong> Mounted on center-line with driver unit center 22,2cm from the top of the baffle.<\/p>\n

Mic position:<\/strong> 1m distance, 14cm above driver unit center (tweeter-axis)<\/p>\n

Smoothing:<\/strong> No smoothing applied.<\/p>\n

 <\/p>\n

\"\"<\/a><\/p>\n

0deg tweeter-axis
\nSample 1 = Blue
\nSample 2 = Red<\/p>\n

Nice consistency between the two driver unit samples. A sharp dip at 1250Hz most likely caused by some sort of cone-edge resonance. Very smooth frequency response between 1.5 -4kHz and with a rising top-end.<\/p>\n

\"\"<\/a><\/p>\n

0deg = Blue
\n15deg = Red
\n22.5deg = Green<\/p>\n

\"\"<\/a><\/p>\n

30deg = Blue
\n45deg = Red
\n60deg = Green<\/p>\n

 <\/p>\n

Distortion:<\/strong><\/strong><\/span><\/h3>\n

 <\/p>\n

Measurement setup:<\/strong><\/em><\/p>\n